METL-SPAN TS PANEL
Allowable Span for Inward or Outward Load of 5 psf
(26 ga. Exterior & 26 ga. Interior Faces)
SINGLE SPAN CONDITION
Allowable Span for Inward or Outward Load of 5 psf
| Thickness (in) | Design Criteria | Allowable Span (ft) | |||
| Bending Stress | Shear Stress | Deflection Limit | Fastener Capacity | ||
| 4 | 30.9 | 79.9 | 26.3 | 49.8 | 26.3 |
| 5 | 33.6 | 94.0 | 30.1 | 57.9 | 30.1 |
| 6 | 36.7 | 104.7 | 33.9 | 66.1 | 33.9 |
| 7&8 | 40.4 | 112.1 | 37.8 | 74.2 | 37.8 |
- Based on TS panel with 26 ga. exterior & 26 ga. interior face (min Fy = 33 ksi) for single span condition.
- Allowable span is the lowest value of panel bending strength, shear strength, deflection limit and connection strength.
- The spans based on panel stress and deflection design criteria are derived from E-72 structural testing. The allowable loads are calculated with a factor of safety of 2.5 and 3.0 for bending and shear stresses, respectively, and deflection limitation of L/240.
- The connection strengths are derived from E-72 structural testing.and the allowable loads are calculated with a factor of safety of 2.5.
- Based on attachment with 14 ga. steel girt with fastener spacing 3"-18"-18"-3" across panel width.
- The structural capacity of the girts are not considered and must be examined independently.
METL-SPAN TS PANEL
(26 ga. Exterior & 26 ga. Interior Faces)
SINGLE SPAN CONDITION
| TS Panel | Design Criteria | Allowable Load (psf) Panel Span (ft) | |||||||||||
| 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | ||
| 4" Thick | Bending & Shear | 79.9 | 66.6 | 57.1 | 49.9 | 44.4 | 39.9 | 36.3 | 33.1 | 28.2 | 24.3 | 21.2 | 18.6 |
| Deflection (L/240) | 106.2 | 84.3 | 68.4 | 56.4 | 47.0 | 39.6 | 33.6 | 28.7 | 24.7 | 21.3 | 18.5 | 16.2 | |
| Connection F1 | 49.8 | 41.5 | 35.5 | 31.1 | 27.6 | 24.9 | 22.6 | 20.7 | 19.1 | 17.8 | 16.6 | 15.6 | |
| 5" Thick | Bending & Shear | 94.0 | 78.3 | 67.2 | 58.8 | 52.2 | 47.0 | 42.7 | 39.2 | 33.5 | 28.9 | 25.2 | 22.1 |
| Deflection (L/240) | 124.3 | 99.7 | 81.8 | 68.2 | 57.6 | 49.1 | 42.1 | 36.4 | 31.6 | 27.6 | 24.2 | 21.3 | |
| Connection F1 | 57.9 | 48.3 | 41.4 | 36.2 | 32.2 | 29.0 | 26.3 | 24.1 | 22.3 | 20.7 | 19.3 | 18.1 | |
| 6" Thick | Bending & Shear | 104.7 | 87.3 | 74.8 | 65.4 | 58.2 | 52.4 | 47.6 | 43.6 | 39.8 | 34.3 | 29.9 | 26.3 |
| Deflection (L/240) | 136.1 | 110.1 | 91.3 | 77.0 | 65.7 | 56.6 | 49.1 | 42.9 | 37.7 | 33.3 | 29.5 | 26.2 | |
| Connection F1 | 66.1 | 55.1 | 47.2 | 41.3 | 36.7 | 33.0 | 30.0 | 27.5 | 25.4 | 23.6 | 22.0 | 20.7 | |
| 7"&8" Thick | Bending & Shear | 112.1 | 93.4 | 80.1 | 70.1 | 62.3 | 56.1 | 51.0 | 46.7 | 43.1 | 40.0 | 36.3 | 31.9 |
| Deflection (L/240) | 141.4 | 115.3 | 96.5 | 82.1 | 70.8 | 61.6 | 54.1 | 47.8 | 42.4 | 37.8 | 33.9 | 30.4 | |
| Connection F1 | 74.2 | 61.9 | 53.0 | 46.4 | 41.2 | 37.1 | 33.7 | 30.9 | 28.6 | 26.5 | 24.7 | 23.2 | |
- Based on TS panel with 26 ga. exterior & 26 ga. interior face (min Fy = 33 ksi). The panel span is single span condition.
- Allowable positive load is the lowest value of panel bending strength, shear strength & deflection limit.
- Allowable suction load is the lowest value of panel bending strength, shear strength, deflection limit and connection strength for each fastener pattern.
- The loads based on panel stress and deflection design criteria are derived from E-72 structural testing. The allowable loads are calculated with a factor of safety of 2.5 and 3.0 for bending and shear stresses, respectively, and deflection limitation of L/240.
- The connection strengths are derived from E-72 structural testing.and the allowable loads are calculated with a factor of safety of 2.5.
- Based on attachment with 14 ga. steel girt with fastener spacing 3"-18"-18"-3" across panel width
- The structural capacity of the girts are not considered and must be examined independently.
METL-SPAN TS PANEL
(26 ga. Exterior & 26 ga. Interior Faces)
TWO OR MORE SPANS CONDITION
| TS Panel | Design Criteria | Allowable Load (psf) Panel Span (ft) | |||||||||||
| 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | ||
| 4" Thick | Bending & Shear | 72.5 | 59.5 | 50.3 | 43.6 | 38.5 | 34.4 | 31.1 | 28.3 | 26.0 | 24.0 | 22.3 | 20.8 |
| Deflection (L/240) | 108.4 | 87.3 | 72.3 | 61.0 | 52.3 | 45.3 | 39.7 | 34.8 | 30.6 | 27.1 | 24.1 | 21.5 | |
| Connection F1 | 48.5 | 40.4 | 34.2 | 29.6 | 26.1 | 23.4 | 21.1 | 19.2 | 17.6 | 16.3 | 15.1 | 14.1 | |
| Connection F2 | 55.6 | 46.2 | 39.1 | 33.9 | 29.9 | 26.7 | 24.2 | 22.0 | 20.2 | 18.6 | 17.3 | 16.1 | |
| 5" Thick | Bending & Shear | 86.4 | 70.9 | 59.9 | 51.9 | 45.7 | 40.8 | 36.9 | 33.7 | 30.9 | 28.5 | 26.5 | 24.7 |
| Deflection (L/240) | 125.9 | 102.0 | 84.9 | 72.1 | 62.1 | 54.1 | 47.6 | 42.3 | 37.7 | 33.6 | 30.1 | 27.1 | |
| Connection F1 | 49.9 | 41.4 | 35.0 | 30.3 | 26.7 | 23.9 | 21.6 | 19.7 | 18.1 | 16.7 | 15.5 | 14.4 | |
| Connection F2 | 60.7 | 50.1 | 42.4 | 36.7 | 32.3 | 28.9 | 26.1 | 23.8 | 21.9 | 20.2 | 18.7 | 17.5 | |
| 6" Thick | Bending & Shear | 97.6 | 80.0 | 67.6 | 58.5 | 51.5 | 45.9 | 41.5 | 37.8 | 34.7 | 32.1 | 29.9 | 27.8 |
| Deflection (L/240) | 137.1 | 111.7 | 93.5 | 79.7 | 69.0 | 60.5 | 53.5 | 47.7 | 42.8 | 38.7 | 35.0 | 31.7 | |
| Connection F1 | 51.3 | 42.5 | 36.0 | 31.1 | 27.4 | 24.4 | 22.1 | 20.1 | 18.5 | 17.1 | 15.9 | 14.8 | |
| Connection F2 | 65.7 | 54.2 | 45.8 | 39.6 | 34.9 | 31.1 | 28.1 | 25.6 | 23.6 | 21.8 | 20.2 | 18.9 | |
| 7"&8" Thick | Bending & Shear | 105.9 | 87.0 | 73.5 | 63.6 | 55.9 | 49.9 | 45.0 | 41.0 | 37.6 | 34.7 | 32.3 | 30.2 |
| Deflection (L/240) | 142.0 | 116.3 | 97.8 | 83.8 | 73.0 | 64.3 | 57.1 | 51.2 | 46.2 | 41.9 | 38.2 | 35.0 | |
| Connection F1 | 52.7 | 43.7 | 37.0 | 32.0 | 28.1 | 25.1 | 22.6 | 20.6 | 18.9 | 17.5 | 16.2 | 15.2 | |
| Connection F2 | 70.7 | 58.5 | 49.5 | 42.8 | 37.6 | 33.5 | 30.3 | 27.6 | 25.3 | 23.4 | 21.7 | 20.3 | |
- Based on TS panel with 26 ga. exterior & 26 ga. interior face (min Fy = 33 ksi) for 2 or more spans condition.
- Allowable positive load is the lowest value of panel bending strength, shear strength & deflection limit.
- Allowable suction load is the lowest value of panel bending strength, shear strength, deflection limit and connection strength for each fastener pattern.
- The loads based on panel stress and deflection design criteria are derived from E-72 structural testing. The allowable loads are calculated with a factor of safety of 2.5 and 3.0 for bending and shear stresses, respectively, and deflection limitation of L/240.
- The connection strengths are derived from E-72 structural testing.and the allowable loads are calculated with a factor of safety of 2.5.
- Fastener Spacing across panel width into 14 ga. Girts:
Connection F1 (3 Fasteners): End Support (3"-18"-18"-3") & Intermediate (7"-14"-14"-7")
Connection F2 (4 Fasteners): End Support (3"-12"-12"-12-3") & Intermediate (5.25"-10.5"-10.5"-10.5"-5.25") - The structural capacity of the girts are not considered and must be examined independently.